ROMAC Racing Products

[racespec]

ROMAC has been synonymous in the industry for its large range of Full Floater Kits to suit Drag and Race Cars. They also manufacture a large range of

- HARMONIC BALANCERS
- SPOOLS
- HIGH PERFORMANCE TIMING CHAIN SETS


ROMAC 8200 SERIES FLOATING HUB KITS - 1500HP Limited

Kit Contents:

* Spindles
* Hubs
* Drive Plates
* End Caps and Screws
* Bearings
* Seals
* O-Rings
* Adj Nuts
* Lock Washers

They are available in both Steel and Alloy Construction. They don't come with Wheel Studs, Axles or Disc Rotors.
When ordering, please specify the following:

1. Major Diameter of the Kit
2. Spline Count
3. Angle
4. Bolt Pattern


Steel Floater Kit - $1750AUS ($1330US)

Alloy Floater Kit - $1925AUS ($1463US)


ROMAC 8300 SERIES FLOATING HUB KITS - Pro Category


Kit contents are the same as the above kit but all ALLOY, but they are limited in

* Spline Count
* Angle
* Bolt Pattern

1. 8300 - Spline Count: 35 Angle: 60 Bolt Pattern: 5 x 5"
2. 8305 - Spline Count: 35 Angle: 60 Bolt Pattern: 5 x 5.5"
3. 8310 - Spline Count: 35 Angle: 90 Bolt Pattern: 5 x 5"
4. 8315 - Spline Count: 35 Angle: 90 Bolt Pattern: 5 x 5.5"
5. 8320 - Spline Count: 40 Angle: 60 Bolt Pattern: 5 x 5"
6. 8325 - Spline Count: 40 Angle: 60 Bolt Pattern: 5 x 5.5"
7. 8330 - Spline Count: 40 Angle: 90 Bolt Pattern: 5 x 5"
8. 8335 - Spline Count: 40 Angle: 90 Bolt Pattern: 5 x 5.5"
9. 8340 - Spline Count: 44 Angle: 60 Bolt Pattern: 5 x 5"
10. 8345 - Spline Count: 44 Angle: 60 Bolt Pattern: 5 x 5.5"
11. 8350 - Spline Count: 44 Angle: 90 Bolt Pattern: 5 x 5"
12. 8355 - Spline Count: 44 Angle: 90 Bolt Pattern: 5 x 5.5"


5" Floater Kit - $3030AUS ($2303US)

5.5" Floater Kit - $3190AUS ($2425US)

We can also supply complete 8300 Series Pro Category Full Packages, please PM or sales@racespec.com.au for pricing and availability


http://www.racespec.com.au/catalog/images/webpics/floater_kit_1.jpg

http://www.racespec.com.au/catalog/images/webpics/floater_kit_2.jpg

http://www.racespec.com.au/catalog/images/webpics/floater_kit_3.jpg

http://www.racespec.com.au/catalog/images/webpics/floater_kit_4.jpg



ROMAC MINI SPOOLS

ROMAC have a huge range of Mini Spools to suit a large range of diffs. The following MINI SPOOLS need to be used with a Two Part Centre Section Only.

1. 28 Spline Ford 9" - 4 Hole For Cross Pins
2. 31 Spline Ford 9" - 4 Hole For Cross Pins
3. 25 Spline Borg Warner - 4 Hole for Cross Pins
4. 23 Spline Banjo Centre - 2 Hole for On Cross Pin
5. 25 Spline Banjo Centre - 2 Hole for On Cross Pin
6. 28 Spline Borg Warner 79 Series Housing - 4 Hole for Cross Pins
7. 28 Spline Salisbury 10 Bolt - One Pin. Fit Factory Conical Shims
8. 10 Spline Early Holdens - EH-HR


Mini Spools - $149.95AUS ($114US)


ROMAC VERNIER CAM GEARS

ROMAC has also started to manufacture a Huge Range of Vernie Cam Gears to suit a wide range of Engines, from Chev right through to Nissan and Holden.
Specifications:

* Aerospace 7075 T6 Alloy
* Red Anodized Finish
* Infinite Adjustment of Cam Pulley
* Easy to read Scale in 2 Degree Increments
* 10 Degrees Advanced or Retard Option
* Aircraft Spec Military Bolts and Washers


http://www.racespec.com.au/catalog/images/RB30_pulley.JPG


RB30 - $230AUS ($175US)
RB20/25/26 - $435setAUS ($331US)

We can source the complete range of ROMAC products, so if there is something that you are looking for, that we have not listed, please PM or sales@racespec.com.au

Thanks

RACESPEC SALES TEAM