M&M Dyanmometer is officially launched.

[Mr-Beast]

M&M dyno is officially launched in Hamala, Kingdom of Bahrain

We tune cars with ECU managment such as:
Hondata, Crome, S-AFC, E-Manage, Ecmlink, Dsmlink, LS-1 Edit, HP tuners, Aem, Haltech and Diablo.
Our prices are as follows:-
Every half hour BD 15
Full tune is 80 BD no matter how long takes (excluding credit price for such as HP tuner which comes around BD 40 for two credits.
Clients may also bring their tuners or tune their car by themselves.

For more information please don't hesitate to contact us on:

Ebrahim Ebrahim AlQattan
+973-36629663
roadbeast79@hotmail.com
EbrahimALGattan@yahoo.com
+973-36629663

Or
Abdulla Aziz Talib
Abdulla.Talib@gmail.com
+973-39423424

[Splash]

mabrook on the launch bro... great deals walla :)

[ZOSicK]

alf mabrook and gluck with your project :up2:

[ZEX]

Mabrook & goodluck

Good prices, and great job on having all those cooling solutions

[MME]

Mabrook guys, allah eewafigkom inshallah. Where is your place exactly?

[-Hussain-]

Mabrook on the new service..

All the best :D

[Black Beast]

mabrook on the dyno bu khalil

wish u all the best!

[BLOODLINE]

I went there for a visit with Black Beast a week ago, great stuff no doubts .. all the best bro :up2:

[LS3_08]

well done guys, very logical price << wish u all da best

[ファルーク]

Mabrook!

What kind of dyno? and is it 4wheel?

[LS3_08]

Mabrook!

What kind of dyno? and is it 4wheel?

nothing for GTR :P

[Drift Master]

all the best bu khaleel

[Attack666]

Mabrook!

What kind of dyno?

[designo]

Mabrook guys! Success in good health inshala!

[K.9978]

do you have a map to the location

[maXmood]

Great tuner, no doubt. :up::up:

Keep up the good work brother.

[Mr-Beast]

Sorry guys it's dynojet but 248 roller not 224 like the other three in Bahrain, no such a difference except our can hold more power not to spin the car at high HP
Same software and numbers etc, bigger break.
We needed to rent Highup to pick it up since the weight is ~ 3 ton the 224 is only ~ 1.5 Ton so you can use forkleft for the 224 but it's impossible for the the 248
The 248 is the first genration of the 224 and used to cost more than the 224, it's rated ofcourse the same up to 2000 WHP with TQ
Any question is welcome

[Mr-Beast]

Thanks man I hope I've done yours the correct way.

[Mr-Beast]

بسيط جدا
اصفهاني ومؤمن على شارع الهملة خل عمارة اصفهاني على يمينك وعمارة مؤمن على يسارك وادخل الداعوس بيك تقاطع سيده المحل رقم 11 على اليسار يم جراج سمكرة وموتر سيكل اسمه بسام كراج التكتولوجيا
او عقب جراج سلمان كاوين اب 3 جراجات
او بجانب زوم جراج
جراج رقم 2787

[Mr-Beast]

I'll post a map shortly.
We can run duel wideband for the v6 and 8 cylindar to be sure all the cylindars are reading =
We have 4 Splite Units two tons which = 8 ton
We have 42" monitor so you can watch your HP AND TQ from outside the dyno
We have 4 kind of fans
One for the front mount intercooler and radiator 1 hp ~ 4000~4400 CFM
Two 12" fans .75 HP for the side intercoolers or the side filters 2800~3300 CFM
One big 48" fan 16500 CFM to make the humidity less and take the smoke out plus one exhaust fan it's big enough to take the smoke out
If I start the air conditioner with in 1 hour in closed area the tempreture reachs 19c and they air conditioner starts to close one by one by them self auto and the Humidity about 16% inside the room
Plus I can run your car outside the room in the air so you get the best result but I usually do that at the end fine tuning
My dyno have 16 hooks I can strap your car from every angle for the FWD and RWD inside and outside the room
I have something called EZ RPM for the cars which can't access to the coils I just set the car on the correct cylindar plus put it in the battery terminals or lighter cigerette

The place is no joke I've build it for accurate wheel hp for my self and for my cars, I didn't care about the business as much as my cars safety.

I've two sets of each strap from dynojet plus everything have been replaced from dynojet except the roller which I bought from www.titanmotorsports.com
I've replaced the following BOB+LPT cable+Speed sensor+RPM signal+Hooks+Breaks+Air pressure regualtor+Serial com cable+O2 sensor cable and the o2 sensor it self I've modified it to read from innovate since each sensor cost $50 and I'm willing to change the sensor every month actually I have like 8 replacement sensors and 12 rpm coil trigger.

If you think I'm lying come and I'll show you how much stuff I have in stock.
I'm not saying mine is the best what I'm trying to say that mine is uniq like Salah one it's 248 not 224
Plus mine has two rollers not single one but shows exactly the same power as the 224 because we are using the same software winpep and same devices which calculate the HP and TQ

Anyone have any question you can call us and we'll be happy to explain everything you want
Our target isn't the money I just want to improve our skill more
Enjoy!

[Mr-Beast]

all the best bu khaleel

Thanks brother long time no see we want to test one of your cars in our dyno:)
Enjoy

[Mr-Beast]

mabrook on the dyno bu khalil

wish u all the best!It's your place at the end:)

[Mr-Beast]

Thanks guys

[gt_mustang]

mashallah i would like to come and dyno my car

do u dyno bikes as well?
i pmed u but didnt get a response

[maXmood]

^not yet..

give the guy a call, cuz he's not a regular on the forum.